こんにちは,れいじです.非パリピです.
電球ソーダとは
https://womagazine.jp/103628womagazine.jp
韓国発祥のオシャレドリンクです.日本の専門店といえばピカピカソーダが有名どころ.
最近は縁日の定番となりつつありますね.
その影響か,この電球ソーダの容器がAmazonやYahooショッピングなどで販売されています.
本家と縁日用の電球ソーダの違いは
本家:そもそものジュースがカラフル.電球のソケット部分にLEDや電球型のストラップがついている.
縁日用:ソケット部分には何もつけないことが多い(ジュースを入れてすぐに提供できるようにするため).ボトルの底がへこんでいて,赤・青・緑のLEDがくっついた基盤がある.ボタンをぽちっと押せば光る仕様.
主にこんなかんじ.
変身前のあんまりエモくないやつ pic.twitter.com/TvtYyg4y0S
— れいじ@技術書典5・CGプログラミング本 (@reiji1020) 2018年8月8日
あんまり光り方がエモくない問題
赤・青・緑のLEDを配置している以上,混色が難しいのでなんだかチープな印象を受けます.
なのでNeoPixel RingとArduino Gemmaを使用して,エモい電球ソーダボトルを作ります.
用意するもの
・Arduino Gemma
・NeoPixel Ring(12個つき)
・リチウムポリマー電池
配線
プログラム
Gemmaがシリアルポートに現れてくれないときはTrinketのドライバをAdafruit公式サイトから落としてきてインストールし,
・ボード:Arduono Gemma(ATTiny85 @8MHz) ・書き込み装置:USBTinyISP
にした状態で,メニューバーのスケッチ > 書き込み装置を使って書き込む を選択すればOKです.
#include <Adafruit_NeoPixel.h> #ifdef __AVR__ #include <avr/power.h> #endif #define PIN 0 // Parameter 1 = number of pixels in strip // Parameter 2 = Arduino pin number (most are valid) // Parameter 3 = pixel type flags, add together as needed: // NEO_KHZ800 800 KHz bitstream (most NeoPixel products w/WS2812 LEDs) // NEO_KHZ400 400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers) // NEO_GRB Pixels are wired for GRB bitstream (most NeoPixel products) // NEO_RGB Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2) // NEO_RGBW Pixels are wired for RGBW bitstream (NeoPixel RGBW products) Adafruit_NeoPixel strip = Adafruit_NeoPixel(60, PIN, NEO_GRB + NEO_KHZ800); // IMPORTANT: To reduce NeoPixel burnout risk, add 1000 uF capacitor across // pixel power leads, add 300 - 500 Ohm resistor on first pixel's data input // and minimize distance between Arduino and first pixel. Avoid connecting // on a live circuit...if you must, connect GND first. void setup() { // This is for Trinket 5V 16MHz, you can remove these three lines if you are not using a Trinket #if defined (__AVR_ATtiny85__) if (F_CPU == 16000000) clock_prescale_set(clock_div_1); #endif // End of trinket special code strip.begin(); strip.show(); // Initialize all pixels to 'off' } void loop() { // Some example procedures showing how to display to the pixels: colorWipe(strip.Color(255, 0, 0), 50); // Red colorWipe(strip.Color(0, 255, 0), 50); // Green colorWipe(strip.Color(0, 0, 255), 50); // Blue //colorWipe(strip.Color(0, 0, 0, 255), 50); // White RGBW // Send a theater pixel chase in... theaterChase(strip.Color(127, 127, 127), 50); // White theaterChase(strip.Color(127, 0, 0), 50); // Red theaterChase(strip.Color(0, 0, 127), 50); // Blue rainbow(20); rainbowCycle(20); theaterChaseRainbow(50); } // Fill the dots one after the other with a color void colorWipe(uint32_t c, uint8_t wait) { for(uint16_t i=0; i<strip.numPixels(); i++) { strip.setPixelColor(i, c); strip.show(); delay(wait); } } void rainbow(uint8_t wait) { uint16_t i, j; for(j=0; j<256; j++) { for(i=0; i<strip.numPixels(); i++) { strip.setPixelColor(i, Wheel((i+j) & 255)); } strip.show(); delay(wait); } } // Slightly different, this makes the rainbow equally distributed throughout void rainbowCycle(uint8_t wait) { uint16_t i, j; for(j=0; j<256*5; j++) { // 5 cycles of all colors on wheel for(i=0; i< strip.numPixels(); i++) { strip.setPixelColor(i, Wheel(((i * 256 / strip.numPixels()) + j) & 255)); } strip.show(); delay(wait); } } //Theatre-style crawling lights. void theaterChase(uint32_t c, uint8_t wait) { for (int j=0; j<10; j++) { //do 10 cycles of chasing for (int q=0; q < 3; q++) { for (uint16_t i=0; i < strip.numPixels(); i=i+3) { strip.setPixelColor(i+q, c); //turn every third pixel on } strip.show(); delay(wait); for (uint16_t i=0; i < strip.numPixels(); i=i+3) { strip.setPixelColor(i+q, 0); //turn every third pixel off } } } } //Theatre-style crawling lights with rainbow effect void theaterChaseRainbow(uint8_t wait) { for (int j=0; j < 256; j++) { // cycle all 256 colors in the wheel for (int q=0; q < 3; q++) { for (uint16_t i=0; i < strip.numPixels(); i=i+3) { strip.setPixelColor(i+q, Wheel( (i+j) % 255)); //turn every third pixel on } strip.show(); delay(wait); for (uint16_t i=0; i < strip.numPixels(); i=i+3) { strip.setPixelColor(i+q, 0); //turn every third pixel off } } } } // Input a value 0 to 255 to get a color value. // The colours are a transition r - g - b - back to r. uint32_t Wheel(byte WheelPos) { WheelPos = 255 - WheelPos; if(WheelPos < 85) { return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3); } if(WheelPos < 170) { WheelPos -= 85; return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3); } WheelPos -= 170; return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0); }
もちろんモバイルバッテリーを使って給電することも可能なのですが,リチウムポリマー電池を使うとよりコンパクトにまとまるのでおすすめです.
Foo pic.twitter.com/aHXmWPTs5x
— れいじ@技術書典5・CGプログラミング本 (@reiji1020) 2018年8月8日
こうなります.めっちゃインスタ映えする.